The flexible all-round protection

NoCut sleeve is a woven protective sleeve made from UHMPE ffor lifting slings and roundslings, which is simply fitted onto the lifting sling. Due to it being used on both sides, the all-round equally high cut resistance offers a long service life and additional operational safety, since handling errors are avoided.

The flexible sleeve construction can also be easily positioned on the sharp edge in confined spaces. During the lifting process, the protective sleeve is placed firmly on the edge of the load, whilst the lifting equipment within the sleeve continues to move freely. A basic prerequisite for lifting and rotating sharp-edged steel, for example.

...

Optimised process technology

Improved cut protection, simplified handing and stronger material stability increase service life and safety.

...

Lightweight

The lightweight construction makes for simple and ergonomic handling.

...

Free positioning

NoCut can be freely positioned over the lifting sling and offers protection at exactly the place where the sharp edge is connected.

...

New Label

NoCut products are marked with a label containing the handling instructions and the general product information. A second label uses colored illustration to show how to use NoCut safely to avoid misuse and increase the safety at work.

...

Certified Safety

A high level of operational safety based on defined edge radii – DEKRA certified.

...

Flexible hose construction

The flexible fabric construction can be positioned easily and blends to the form of the edge.

In order to protect the lifting sling, the NoCut sleeve may be used as follows:

Fig. 1 For lifting belts

Simply fitted

Fig. 3 For roundslings*

Using both strands

Fig. 5 For roundslings

Single strand [factory-made]

New Fig. 3 For roundslings

With center seam by using both strands [factory-made]

NoCut sleeve with center seam
Simply better and stronger!

Simply better and stronger! Three good reasons for using the new NoCut sleeve. The center seam simplifies the use of the NoCut sleeve when lifting with round slings using both legs [shown in Fig. 3]. The middle seam sperates each of the round sling strands in a single channel. It prevents the round sling strands from overlapping and cut through inside the NoCut sleeve. Fitted across both legs of the roundsling, manual adjustment is not required and the two strands are bound together in such a way that the sleeve cannot be removed. Take advantage of longer service lives, additional safety and the variety of combinations with different lifting slings!

*The permitted usable length of the NoCut sleeve over both strands of a roundsling may amount to 1 metre maximum.

Working together by design

It goes without saying that NoCut sleeve has been adapted to the different widths of the SpanSet lifting slings and roundslings. For this reason, NoCut sleeve is excellently suited to protecting textile lifting slings such as PowerStar lifting slings and SupraPlus roundslings. NoCut cut protection offers a lightweight and compact construction for especially ergonomic handling with a low level of effort.


Usage of NoCut sleeve for round slings over both strands above 1 metre length is permitted only with middle.
Type ca. inner width [mm] ca. outer width [mm] ca. weight [kg]
NCS-055 55 65 0,4
NCS-075 75 85 0,6
NCS-105 105 115 0,8
NCS-135 135 145 1,1
NCS-165 165 175 1,4
NCS-195 195 205 1,6
NCS-255 255 265 2,0
NCS-315 315 325 2,7
  Lifting belts Round slings
Type Fig. 1 Fig. 3 Fig. 3 with middle seam Fig. 5
NCS-055 PB 1.000,
HB 1.000
- - SupraPlusX 500, 1.000,
SupraPlus 500, 1.000,
TwinTex 1.000,
Liftfix 500, 1.000
NCS-075 PB 2.000,
PCS 2.000,
HB 2.000
SupraPlusX 500,
SupraPlus 500,
TwinTex 1.000, 2.000,
Liftfix 500
- MagnumX 10.000,
SupraPlusX 2.000, 3.000, 4.000, 5.000,
SupraPlus 2.000, 3.000, 4.000, 5.000,
TwinTex 2.000, 3.000, 4.000, 5.000,
Liftfix 2.000, 3.000, 4.000, 5.000
NCS-105 PB 3.000,
PCS 4.000,
HB 3.000
SupraPlusX 1.000, 2.000, 3.000,
SupraPlus 1.000, 2.000, 3.000,
TwinTex 3.000,
Liftfix 1.000, 2.000, 3.000
SupraPlusX 500,
SupraPlus 500,
TwinTex 1.000, 2.000,
Liftfix 500
MagnumX 20.000,
MagnumForce 10.000,
SupraPlusX 6.000, 8.000,
SupraPlus 6.000, 8.000,
TwinTex 6.000, 8.000
Liftfix 6.000, 8.000
NCS-135 PB 4.000,
PCS 6.000,
HB 4.000
MagnumX 10.000,
SupraPlusX 4.000, 5.000, 6.000,
SupraPlus 4.000, 5.000, 6.000,
TwinTex 4.000,
Liftfix 4.000, 5.000
MagnumX 10.000,
SupraPlusX 1.000, 2.000, 3.000,
SupraPlus 1.000, 2.000, 3.000,
TwinTex 3.000,
Liftfix 1.000, 2.000, 3.000
MagmumX 30.000,
MagnumForce 20.000, 30.000,
MagnumPlus 10.000, 15.000,
Liftfix 10.000, 15.000
NCS-165 Liftfix 5.000,
PB 5.000,
PCS 8.000
MagnumX 20.000,
MagnumForce 10.000,
SupraPlusX 8.000,
SupraPlus 8.000,
TwinTex 5.000, 6.000, 8.000,
Liftfix 6.000, 8.000
SupraPlusX 4.000, 5.000, 6.000,
SupraPlus 4.000, 5.000, 6.000,
TwinTex 4.000,
Liftfix 4.000, 5.000
MagnumX 40.000
MagnumForce 40.000,
MagnumPlus 20.000, 25.000,
Liftfix 20.000, 25.000
NCS-195 PB 6.000,
PCS 10.000,
HB 6.000
MagnumX 30.000,
MagnumForce 20.000,
MagnumPlus 10.000,
Liftfix 10.000
MagnumX 20.000,
MagnumForce 10.000,
SupraPlusX 8.000,
SupraPlus 8.000,
TwinTex 5.000, 6.000, 8.000,
Liftfix 6.000, 8.000
MagnumPlus 30.000,
MagnumForce 50.000, 60.000,
Liftfix 30.000
NCS-255 PB 8.000,
PCS 12.000,
HB 8.000
MagnumX 40.000, 50.000,
MagnumForce 30.000,
MagnumPlus 15.000,
Liftfix 15.000
MagnumX 30.000,
MagnumForce 20.000,
MagnumPlus 10.000,
Liftfix 10.000
MagnumPlus 40.000, 50.000
MagnumForce 80.000, 100.000,
Liftfix 40.000, 50.000
NCS-315 PB 10.000,
PCS 16.000,
HB 10.000
MagnumX 60.000,
MagnumForce 40.000,
MagnumPlus 20.000, 25.000,
Liftfix 20.000, 25.000
MagnumX 40.000, 50.000,
MagnumForce 30.000,
MagnumPlus 15.000,
Liftfix 15.000
-
PB - PowerStar 2 layers, PCS - PowerStar 4 layers, HB - Liftfix 2 layers
Lifting device NoCut sleeve
Radii [mm] 1 2
Lifting belts:
Liftfix [HB] ≤ 5t
PowerStar 4layers [PCS] ≤ 10t
Round slings:
SupraPlus, SupraPlusX, Twintex, Liftfix ≤ 5t
MagnumPlus, SupraPlus, SupraPlusX, Twintex, Liftifx ≤ 10t
MagnumPlus, Liftifx ≤ 20t
MagnumPlus, Liftifx ≤ 25t
MagnumPlus, Liftifx ≤ 30t
Magnum-X ≤ 10t
Values in the table marked with refer to the minimum radius where NoCut may still be employed. Larger edge radii are included in the respective labelling.